Lab on Monday!!!!
Make sure to bring proper clothing (Pants, closed shoes, no contacts, etc.)
1 table = 1 (side of) paper!
Part II.
I - Title: Melting Temperature of a Solid
II - Purpose: To observe a change of state while identifying a pure unkownk solid while learning the proper use of:
Bunsen Burner
Ring Stand
Waterbath
Observe a change state, A physical change while carefully making Quantitative and Qualitative observations.
III Procedure:
Significant changes to manual
Come in, obtain a bunsen burner, A ring stand, wire gauze, Test tube containing a solid w/ a thermometer beaker, 2nd Thermometer, and a Flint
Flint is NOT a TOY it is a TOOL
SAFETY - Hair back!!
Burner Use
Barrel - oxygen supply - close all the way to right, use Gas Valve to control the methane amount. - Close all the way down, then open 1/4th of a turn
Once setup - control the gas at stopcock
Ring Stand Set Up
Place ring over base
SAFETY - Do NOT place to the side or back
Tripod type - Place close to one leg
Test Tube Holder
Check Swivel
Make sure clamped tight to
Appropriate Adjustment to hold JUST BELOW the lip og the test tube
Place test tube carefully out of harms way
Remove test tube off of stand while heating the water bath
Water Bath
Heat the Bath to 60 - 65 degrees Celsius
When at 64 degrees turn off gas and then remove burner
Take temperature of the water - Enter on table (see below)
1 page per table (1 for melting, 1 for freezing.
Place a 400ml beaker 3/4 full of warm tap water,
Related Documents: Essay about Chemistry: Temperature
How quickly or how often the molecules and atoms move and collide determine the temperature also determining the state of matter and the kinetic energy. The faster they are moving the higher the object’s temperature, the higher the kinetic energy. Kinetic energy is simply the fact that a moving object can do work on anything it comes in contact with. The formula to find the average kinetic energy at a given temperature is KE =32KT There are three phases of matter known as solids, liquids, and…
Coexistence Curves • Under a range of temperature and pressure conditions one can have liquid and vapor (gas) in dynamic equilibrium. Gas phase molecules are entering the liquid at the same rate as liquid phase molecules are evaporating. (No heat needs to be supplied for this process to occur. Why?) The simplest cases involve a pure liquid and a pure gas in equilibrium. Normal boiling point! Most volatile liquid. Why? Molecules of liquid “e” have the strongest intermolecular forces. Why? Least…
Determination of Molar Mass by Freezing-Point Depression When a solute is dissolved in a solvent, the freezing temperature is lowered in proportion to the number of moles of solute added. This property, known as freezing-point depression, is a colligative property; that is, it depends on the ratio of solute and solvent particles, not on the nature of the substance itself. The equation that shows this relationship is ΔTf = Kf × m× i where ΔTf is the freezing point depression, Kf is the freezing point…
is the most abundant compound on Earth's surface, covering about 70 percent of the planet. In nature, water exists in liquid, solid, and gaseous states. It is in dynamic equilibrium between the liquid and gas states at standard temperature and pressure. At room temperature, it is a tasteless and odorless liquid, nearly colorless with a hint of blue. Many substances dissolve in water and it is commonly referred to as the universal solvent. Because of this, water in nature and in use is rarely pure…
°C thermometer was calibrated using 3 calibration points. The freezing point mark was calibrated using crushed ice and distilled water and a final temperature of 0.15°C was recorded with a -0.15°C calculated correction factor (see Table 1). For the boiling point, distilled water was boiled and the thermometer was placed in the vapour and a temperature of 102.1°C was recorded. The correction factor was calculated to be -2.2 °C, taking into account the atmospheric pressure of 757.4 mm Hg. For the…
fan 01/28/2015 Chemistry 1220 T.A. - Drew Adkins Purpose: Use laboratory techniques to explore two factors that affect solubility: temperature and solute-solvent interactions. Quantify the solubility and use graphing techniques to study the solubility trends as a function of temperature. Compare the presentation of solubility data by using different units. Procedure: Refer to pages 20 to 23 of General Chemistry 1220 laboratory Manual, Volume 1 by Department of Chemistry The Ohio State…
Abstract This lab is performed in order to determine the total energy in a reaction between zinc and hydrochloric acid. The reaction is done twice, once to measure the heat of the reaction and again to determine the work done in the system. This is because Enthalpy equals heat plus work (∆H= ∆E+W). Heat and work can be broken down further into separate components so the equation used in lab is ∆H=mc∆T + PV. Many calculations are used in the lab to find out what cannot be measured directly (ex:…
filtration for long enough to sufficiently dry. Introduction Redox reactions are an important class of reactions in organic chemistry that involve the transfer of electrons from…
Chemistry Notes [Exam2] Ionic and Covalent Bonding [Chaps 6.3-6.4] Opposites Attract Metal +Nonmetal=Ionic Bond Recall positive is attracted to negative charge When a metal atom donates an electron to a non-metal atom, an Ionic bond occurs Ionic Bonds are Predictable Ion charges of Calcium and Fluorine: Ca2+ F- Always from neutral compounds Al3+ and O2- These compounds are very stable over time Sharing can bring happiness In Ionic Bonding: The transfer of the electrons from one atom to a different…
the experiment was to introduce the chemistry student to basic laboratory procedures and demonstrate working knowledge of the equipment used and all safety rules. A 20cm piece of glass tubing was broken and heated for 28 seconds until it was bent into a 90 degree angle. A beaker was filled with 250mL of water with an initial temperature of 22 degrees Celsius. The water was then boiled and the temperature was reported to be 103 degrees Celsius; the temperature range was 81 degrees Celsius. Lastly…